Worth AnchorMate Anchor Reel System

The Worth AnchorMate Anchor Reel Anchor Control System is a simple solution to store your anchor lines. To order, shop at Wholesale Marine.
Worth AnchorMate Anchor Reel Anchor Control System Anchor control systems can be used to store your anchor lines and anchor systems. These systems are designed to help in anchoring and provide a safe and easy solution. The Worth Anchormate is the original anchor control system. Using this anchor system is as easy as turning a button. The free-spooling real will stop anywhere you need it. When the anchor control system is not in use it is held in place with the bow fixture. The lines are held in place and wrap around the reel. The Worth Anchormate is constructed with a heavy steel gauge with electrostatic powder-coated finish. The rollers are self-lubricating and provide for a smooth and quiet operation. Installation is easy with the 3-point bracket on the reel and fits most areas on the boat including flat or curved hulls. The system is designed to hold 100’ of 3/16” nylon braided rope. The rope is sold separately. Features: Anchor lowers with the turn of a button Smooth, quiet operation Mounts in any convenient location in boat Contains (1) No. 100 Anchor Reel Contains (1) No. 50 Bow Fixture Rope and mounting hardware no included Made in the USA Specifications: Construction: Heavy gauge steel with electrostatic powder coated paint finish & self lubricating nylon rollers Recommended anchor style: mushroom or river special Recommended anchor weight: 8-12 lbs. Line Capacity: 100' of 3/16 nylon braided rope How to Install your Worth Anchormate Mounting hardware NOT included. For installation you will need: 3 bolts or screws to fasten the Anchormate reel - 4 bolts or screws to fasten the bow mount Installation: Place Bow Mount on corner of boat, mark and drill 4 holes to match base of mount. On boats with a deck, or no opening in bow plate, drill a 3/4 hole directly beneath rear Bow Mount pulley for anchor line to pass through. Attach Bow Mount with 1/4 bolts. Self tapping sheet metal screws or wood screws may be used depending on boat's construction. Place Anchor Reel on either side of boat near oar locks or transom as desired. IMPORTANT! Be sure to leave clearance so that the reel will not interfere with the operation of oars or motor. Mark and drill three holes to match reel mounting brackets. Attach with ¼ bolts placing the 6 nylon washers on each side of hull to make installation watertight. Note: Although line guides are not necessary, they are recommended to keep anchor line along the side of the boat and out of the way. Install the pulley - We recommend the use of a swivel pulley on boats which have a deck or bow plate. To install thread anchor line from reel, through line guides and the unmounted swivel pulley (not furnished), then up through deck or bow plate, and over pulleys in bow mount as shown. Attach anchor, or weight, to take up line slack and cause tension on the line. Grasp swivel pulley (a tiller pulley is ideal) and position inside of bow directly beneath rear bow mount pulley. Mark holes and attach pulley. Be certain that the swivel pulley does not rub on deck or bow plate and that anchor line does not rub on edge of hole in deck. Reel Operation Instructions: To release the anchor, simple turn the control button in a clockwise direction. The anchor will drop until you release the button or the anchor hits bottom. To raise the anchor, turn the handle clockwise Note: Do not turn button or handle counter clockwise. Damage may result. Lubrication: The reel is factory lubricated with waterproof grease, however, periodic lubrication is required. To do this, follow the disassembly instructions. The frequency of this procedure will depend on the amount of exposure to the elements. The reel and bow fixture should be covered if possible when stored outside, and should be flushed with fresh water after each use in saltwater.

Anchormate II Installation Instructions

Original Anchormate Disassembly Instructions

Attwood Anchor System Installed On A Jon Boat / Boat Mods / Jon

Attwood Marine 13710-4 Anchor Rope & ChainAnchor Lift SystemThis convenient system drops the anchor at the turn of a button and stores it in the anchor mount housing when not in use. Constructed of heavy gauge steel with durable powder coated finish and mounts on the bow or stern corners of most boats.Anchor secures within anchor mount housing. Mounts easily to bow or stern. Deploy anchor with the simple twist of a knob.

Attwood - 13710-4 - Anchor Lift System

Anchormate ll worth boat anchor system, white.

Customer reviews: Anchormate Worth Anchor Reel, Black

Anchor Mate 2 - Search Shopping

, Replacement AnchorMate Reel for use with the Worth AnchorMate Anchor Control System. This reel is constructed of heavy gauge steel with an

Worth AnchorMate Reel

New, The Anchormate II will accommodate about 150 feet of 3/16 nylon rope (not included) and anchors up to 18 pounds. The bow fixture utilizes an

Worth Company Anchormate II anchor control. for Sale in Lake Worth, FL - OfferUp

Worth 07536 Anchormate II Bow Anchor Holder for sale online